自动化切割配套除尘设备 粉尘清理解决方案

工作原理
含尘气体在离心风机的离心力作用下进入除尘器匀流室，进入匀流室后由于气流断面突然扩大及气流分布板作用，气流中一部分粗大颗粒在动和惯性力作用下直接沉降到灰斗；粒度细、密度小的尘粒进入各滤尘室后，通过布朗扩散和筛滤等组合效应，使粉尘沉降在滤芯表面上，净化后的气体进入净气室由排风管经风机排出。设备的阻力随着滤袋表面粉尘层厚度的增加而增大。阻力达到某一设定值时进行清灰。此时集尘器PLC程序控制电磁脉冲阀逐个开启，压缩空气以极短的时间通过诱导喷嘴涌入滤筒，使滤筒膨胀变形产生振动，并在逆向气流冲刷的作用下，附着在滤筒外表面上的粉尘被剥离落入灰斗中。脉冲除尘器是在JC型的基础上，改进的新型高效脉冲除尘器。净化效率高，处理气体能力大，性能稳定，滤袋寿命长，操作方便，维修工作量小等优点。

1、高精度用型滤材，亚微米级过滤效率99%以上，确保达标排放
2、高效除尘用风机，吸力强、风量大、噪音低、效率高、运转平稳
3、滤袋直立安装，过滤面均匀，停机振打清灰，避免粉尘二次吸附
4、立柜式机体占地面积小，可加装万向脚轮，增加设备适用性
5、设备具有过热、短路保护功能，确保设备运行稳定安全
6、滤袋组合方便使用成本省，多用于干性大浓度粉尘的收集
7、适合无压缩气源场合使用，大大增加除尘器适用范围

 在抛光、切割、打磨、粉碎、焚烧（燃烧）、等工业生产过程中，产生碎屑、烟雾、或者粉尘等微细颗粒物，通过除尘设备把这些微细颗粒物从气体中分离出来的过程为工业除尘的过程。除尘设备包括：吸尘罩、除尘管道、除尘器、风机等部分组成。吸尘罩：吸尘罩的形状与大小根据产尘点的大小和所需要的风速来决定，通常，吸尘罩需要尽量的靠近产尘点，吸尘罩的断面风速要足以克服颗粒物的重力和周围环境的风速，另外，吸尘罩的设计需要尊随两个原则，*、要把产尘点周围的粉尘浓度降到不足以影响工人健康的浓度，第二、不妨碍工人的日常操作。第三、不引起安全事故（主要是对风速和断面大小的控制，当风速和断面大小足够的大时，可以把其周围的轻质物体吸尽吸风管道）。

 In the process of polishing, cutting, grinding, grinding, burning and other industrial production, fine particles such as debris, smoke, or dust are produced. The process of separating these fine particles from the gas by dust removal equipment is the process of industrial dust removal. Dust removal equipment includes: dust hood, dust removal pipeline, dust collector, fan and other parts. Dust hood: the shape and size of the dust hood are determined according to the size of the dust producing point and the required wind speed. Generally, the dust hood needs to be as close to the dust producing point as possible, and the cross-section wind speed of the dust hood should be enough to overcome the gravity of particles and the wind speed of the surrounding environment. In addition, the design of the dust hood should follow two principles: *, the dust concentration around the dust producing point should be reduced to not enough to affect the work The concentration of human health, second, does not interfere with the daily operation of workers. Third, it will not cause safety accidents (mainly the control of wind speed and cross-section size. When the wind speed and cross-section size are large enough, the light objects around it can be absorbed by the suction pipe).

日常如何保养和维护：
1及时清理桶内杂物和各吸尘附件,尘格尘袋在每次工作后清洁, 检查有没穿孔或漏气,并用清洁剂加温水*清洁尘格和尘袋,并吹干,严禁使用不干爽的尘格尘袋.
2检查电源线及插头是否有破损,用完后把电源线圈绕成一扎挂置于机头顶盖zb 272吸尘器挂钩上
3吸水工作完毕后检查进风口有无堵塞或杂物,否则需作清理.检查浮波有无破损

自动化切割配套除尘设备 粉尘清理解决方案