一、概述
BS-2008型
全自动闭口闪点测试仪（中英文版），用于测定石油产品的闭口闪点值。本仪器采用彩色液晶屏幕显示，全中文人机对话界面，无标识键盘，开放式、模糊控制集成软件，模块化结构等技术；对可预置温度、试样标号、大气压强、试验日期等参数具有提示菜单，导向式输入的工作方式。本仪器自动化程度高，使用方便、快捷，符合中华人民共和国标准GB/T261-2008《闪点的测定 宾斯基-马丁闭口杯法》规定的试验要求，是理想的同类进口仪器的替代产品，可广泛用于铁路、航空、电力、石油行业及科研部门。
二、适用标准及适用范围
本仪器是根据国家标准GB/T261-2008《闪点的测定 宾斯基-马丁闭口杯法》所规定的要求设计制造的。适用于按该标准规定的方法,测定石油产品用闭口杯、在规定条件下,加热到它的蒸汽与空气的混合气接触火焰发生闪火时的zui低温度，即闭口杯法闪点。
三、主要技术指标和参数
1、工作电源 AC220V±10%， 50Hz；
2、温度测量 量程 室温～350℃；
重复性 ≤2℃；再现性 ≤4℃；
分辨性 0.1℃；精度 0.5%；
3、基数参数 升温速度 符合GB/T261-2008标准；
点火方式 电子点火、气体火焰；
4、环境温度 （10～40）℃；相对湿度 ≤80%；
5、整机功耗 不大于500W。
四、工作原理
全自动闭口闪点测试仪（中英文版）在国家标准GB/T261-2008规定的条件下，把试样装入试验杯，对装有试验油的试验杯加热，产生的石油蒸气与周围空气形成的混凝合成气体在火焰接触发生闪火时的zui低温度作为闪点。
计算机根据所采集的温度变化情况由I/O口发出指令，控制加热器，使试验油温度按一定速率上升，扫描周期、点火时间、微分检测等均实施自动控制，当闪火被测出时，计算机系统停止数据采集，显示闪火温度并打印记录结果，停止加热，关闭火焰，大臂自动抬起，实验结束。
五、成套性
1、测试仪仪器成套
序号 | 名 称 | 单位 | 数量 |
1 | 测试仪 | 台 | 1 |
2 | 油杯 | 个 | 1 |
3 | 电源线（250V 10A） | 根 | 1 |
4 | 打印纸 | 卷 | 1 |
5 | 点火丝 | 个 | 5 |
6 | 点火器 | 把 | 1 |
The instrument is used to determine closed cup flash point of petroleum products. The instrument adopts colored LCD screen, man machine conversation interface, blank buttons, open and fuzzy controlled integration software, and modular structure. It can preset temperature, sample ID, barometric pressure, test date, and other parameters. It has prompt menu and input guide. The instrument is automatic, convenient, and rapid. It can meet the requirements of the National Standard of People’s Republic of China GB/T261-2008 “Test Methods for Flash Point of Petroleum Products （Pensky-Martens Closed Cup Method）”. It is the best choice of similar products. It can be widely used in the field of railway, aviation, power plant, petroleum industry, and scientific research institutes.
II. Purpose and scope
The instrument is designed and made as per the National Standard GB/T261-2008 “Test Methods for Flash Point of Petroleum Products （Pensky-Martens Closed Cup Method）”. It is suitable to determine closed cup flash point of petroleum products, which is expressed as the lowest temperature when the mixture of its vapor and air contacts flame and appears flash, using a closed oil cup under the stipulated condition.
III. Main technical specification and parameters
1. Power supply: AC 220V±10%, 50 Hz;
2. Temperature measurement:
（1） Full scale: room temperature～350℃;
（2） Repeatability: ≤2℃;
（3） Reproducibility: ≤4℃;
（4） Resolution: 0.1 ℃;
（5） Accuracy: 0.5%;
3. Basic parameters:
（1） Temperature rising speed: as per GB/T261-2008;
（2） Ignition mode: Electron device for ignition; gas flame for flame application;
4. Working environment:
（1） Ambient temperature: 10～40℃;
（2） Relative humidity: ≤80％;
5. Total power consumption: not more than 300 W;
IV. Working principle
Fill sample in the test cup, and heat the test cup containing sample on the instrument as per the requirements of the National Standard GB/T261-2008. The flash point is expressed as the lowest temperature when the mixture of sample vapor and air contacts flame and appears flash.
The controlling system can send orders through I/O port as per the collected temperature changes to control the heater, so that the sample temperature will increase at a certain rate. The
V. Full set and technical documents
1. Full set
No. | Name | Unit | Quantity |
1 | Main unit | Set | 1 |
2 | Oil cup | Piece | 1 |
3 | Power supply wire （250V 6A） | Piece | 1 |
4 | Printing paper | Roll | 1 |
2. Technical documents
（1） Operation Manual 1 piece
（2） Quality Certificate 1 piece
（3） Repair Guarantee 1 piece
flame application interval, flame application time, and flash detection can be automatically controlled. When a flash is detected, the controlling system will stop collecting data. Then the instrument will show flash point value and print out test results. The heater will stop working, the flame is extinguished, and the test arm is automatically raised up. The test is over.
