CHEMTRONICS

MSDS #1404
Page 1 of 2
SECTION 1: CHEMICAL PRODUCT AND COMPANY INFORMATION
Company Address:
8125 Cobb Center Drive
Kennesaw, GA 30152
Product Information: 800-TECH-401 Emergency: （Chemtrec）
Customer Service: Revision Date: February 23, 2005
Product Identification
SODER-WICK LEAD-FREE SD
Product Code: 40 Series
SECTION 2: COMPOSITION, INFORMATION ON INGREDIENTS
Product Ingredient Information CAS# Wt. % Range
Copper 7440-50-8 98.0-99.0
Rosin 8050-09-7 1.0-2.0
SECTION 3: HAZARD IDENTIFICATION
Emergency Overview: Shiny, braided copper wire. This product is nonflammable.
Potential Health Effects:
Eyes: No effect expected under normal conditions of use. Vapors released from other materials used in the desoldering process may cause eye irritation.
Skin: Prolonged contact may cause skin irritation.
Ingestion: Harmful if swallowed. Metal contact may be irritating to mouth, throat and stomach tissues.
Inhalation: No effects expected under normal conditions of use. Vapors from other materials used in the desoldering process may cause irritation of the mouth, nose
and throat.
Pre-Existing Medical Conditions Aggravated by Exposure: None known.
SECTION 4: FIRST AID MEASURES
Eyes: Usually not required. If eye irritation occurs immediay flush with plenty of water. After initial flushing , remove any contact lenses and continue flushing
for at least 15 minutes. Have eyes examined and tested by medical personnel if irritation develops or persists.
Skin: Usually not required . If skin irritation occurs wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation develops
or persist. Wash clothing separay before reuse.
Ingestion: Do not induce vomiting. Get immediate medical attention.
Inhalation: If user is overcome by fumes during the desoldering process, remove victim to fresh air. If not breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: Nonflammable LEL/UEL: Not applicable
Extinguishing Media: Water fog, CO2, dry chemical, foam are compatible for extinguishing fires involving other materials when Soder-Wick is present.
Fire Fighting Instructions: As in any fire, wear self-contained breathing apparatus （pressure-demand, MSHA/NIOSH approved or equivalent） and full protective gear.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Small Spills: Pick up spilled braid. If soiled or dirty store in a closed container for delivery to a metals recycling center. Do not dispose of by placing in trash.
SECTION 7: HANDLING AND STORAGE
Avoid prolonged or repeated contact with eyes, skin. Wash hands before eating. Use with adequate ventilation. Avoid breathing vapors given off by he desoldering
process. Store in a cool dry place. Keep container closed when not in use. KEEP OUT OF REACH OF CHILDREN.
SECTION 8: EXPOSURE CONTROLS/PERSONNEL PROTECTION
Exposure Guidelines:
CHEMICAL NAME ACGIH TLV OSHA PEL ACGIH S
Copper 0.2 mg/m3 1.0 mg/m3 NA
Rosin NA NA NA
Work/Hygienic Practices: Good general ventilation should be sufficient to control airborne levels of desoldering process vapors. Local exhaust ventilation may be
necessary to control any air contaminants to within their TLVs during the use of this product. Wear safety glasses with side shields or goggles when using this product.
NFPA and HMIS Codes: NFPA HMIS
Health 1 1
Flammability 0 0
Reactivity 0 0
Personal Protection - -
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Rosin coated braided copper wire Solubility in Water: Insoluble
Odor: Mild Specific Gravity: NA
pH: NA Evaporation Rate: NA
Vapor Pressure: NA Viscosity: NA
Vapor Density: NA Percent Volatile: NA
Color: Copper metallic Boiling Point: NA
CHEMTRONICS

MSDS #1404
Page 2 of 2
SECTION 10: STABILITY AND REACTIVITY
Stability - This product is stable. Conditions to Avoid: None known
Incompatibility: Do not mix with powdered alkali and alkaline earth metals or strong oxidizing agents.
Products of Decomposition: Carbon dioxide, carbon monoxide.
Hazardous Polymerization: Will not occur
Conditions to Avoid: NA
SECTION 11: TOXICOLOGICAL INFORMATION
Inhalation:
Inhalation of dust and fumes during desoldering can irritate the respiratory tract.
Ingestion:
Not expected to be a route of exposure.
Skin:
May cause allergic skin reaction in some individuals.
Eye:
Contact with rosin dust and desoldering fumes can irritate the eyes.
Cancer Information: No ingredients listed as human carcinogens by NTP or IARC
Reproductive effects: none Teratogenic effects: none Mutagenic effects: none
SECTION 12: ECOLOGICAL INFORMATION
Environmental Impact Information
Avoid runoff into storm sewers and ditches which lead to waterways. Water runoff of desoldering process residues may cause environmental damage.
REPORTING
US regulations require reporting spills of this material that could reach any surface waters. The toll free number for the US Coast Guard National Response Center is:
1-
SECTION 13: DISPOSAL CONSIDERATIONS
Dispose of in accordance with all federal, state and local regulations.
SECTION 14: TRANSPORTATION INFORMATION
Proper
Shipping Name
Air: Wire Not regulated
Ground: Wire Not regulated
SECTION 15: REGULATORY INFORMATION
SECTION 313 SUPPLIER NOTIFICATION
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To-Know
Act of 1986 （40 CFR 372）.
Chemical Name CAS# Wt. % Range
Copper 7440-50-8 98.0-99.0
This information should be included on all MSDSs copied and distributed for this material.
TOXIC SUBSTANCES CONTROL ACT （TSCA）.
All ingredients of this product are listed on the TSCA Inventory.
WHMIS: Not hazardous. This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of the information required by the
CPR.
SECTION 16: OTHER INFORMATION
Product should be used only with adequate ventilation to remove vapors produced during the desoldering process. Mechanical ventilation should be used when large
amounts of fumes are produced.
To the best of our knowledge, the information contained herein is accurate. However, all materials may present unknown hazards and should be used with caution. In
particular, improper use of our products and their inappropriate combination with other products and substances may produce harmful results which cannot be
anticipated. Final determination of the suitability of any material is the sole responsibility of the user. Although certain hazards are described herein, we cannot
guarantee that these are the only hazards that may exist.