西门子6RY1703-0DA02
时间:2019-10-31 阅读:80
-
提供商
河南兆阳自动化科技有限公司 -
资料大小
36979 -
资料图片
点击查看 -
下载次数
25次 -
资料类型
jpg -
浏览次数
80次
时间:2019-10-31 阅读:80
提供商
河南兆阳自动化科技有限公司资料大小
36979资料图片
点击查看下载次数
25次资料类型
jpg浏览次数
80次西门子6RY1703-0DA02
BOP20 基本操作员面板
操作员面板 AOP30
CBC10 通讯板
CBE20 通讯板
端子板 TB30
终端模板 TM31
电压检测模板 VSM10
机柜安装式编码器模板 SMC30
信号电缆
TB30 Terminal Board
The TB30 Terminal Board supports the addition of digital inputs/digital outputs and analog inputs/analog outputs to a Control Unit.
The following are located on the TB30 Terminal Board:
A shield connection for the signal cable shield is located on the Control Unit.
西门子6RY1703-0DA02
The TB30 Terminal Board is inserted in the slot to optionally expand the CU320‑2 Control Unit.
Connection example of a TB30 Terminal Board
| TB30 Terminal Board 6SL3055-0AA00-2TA0 |
---|---|
Power requirement, max. at 24 V DC via Control Unit CU320‑2 without taking account of digital outputs | 0.05 A |
| 2.5 mm2 |
| 20 A |
Digital inputs In accordance with IEC 61131‑2 Type 1 |
|
| -3 ... +30 V |
| -3 ... +5 V |
| 15 ... 30 V |
| 6 mA |
|
|
| 50 μs |
| 100 μs |
| 0.5 mm2 |
Digital outputs (continuously short-circuit proof) |
|
| 24 V DC |
| 500 mA |
| 150 μs |
| 0.5 mm2 |
Analog inputs difference |
|
| -10 ... +10 V |
| 65 kΩ |
| 13s bit + sign |
| 0.5 mm2 |
Analog outputs (continuously short-circuit proof) |
|
| -10 ... +10 V |
| -3 ... +3 mA |
| 11 bits + sign |
| 200 μs |
| 0.5 mm2 |
Power loss, max. | 3 W |
Weight, approx. | 0.1 kg (0.22 lb) |
Certificate of suitability | cULus |
使用终端板卡 TB30,可以扩展控制器 CU320 的数字量输入和数字量输出以及 CU320-2 控制单元模拟量输入和模拟量输出的数量。
TB30 端子板上有以下接口:
TB30 端子板插在控制器的选件插槽内。
信号线屏蔽的屏蔽底座位于 CU320-2 控制单元上。
TB30端子板的典型连接
TB30 端子模板 | |
---|---|
规定电流,大 24 V DC 时 | 0.05 A |
| 2.5 mm2 |
| 20 A |
数字量输入 entsprechend IEC 61131-2 Typ 1 | |
| -3 … +30 V |
| -3 … +5 V |
| 15 … 30 V |
| 10 mA |
| |
| 50 μs |
| 100 μs |
| 0.5 mm2 |
数字量输出 | |
| 24 V DC |
| 500 mA |
| 150 μs |
| 0.5 mm2 |
模拟量输入 | |
| -10 … +10 V |
| 65 kΩ |
| 13 位 + 符号 |
| 0.5 mm2 |
模拟量输出 | |
| -10 … +10 V |
| -3 … +3 mA |
| 11 位 + 符号 |
| 200 μs |
| 0.5 mm2 |
功耗 | < 3 W |
重量,约 | 0.1 kg |
认证, | cULus |
需要使用机柜安装式编码器模板 SMC30 来分析不带 DRIVE-CLiQ 接口的电机编码器。还可通过 SMC30 连接外部编码器。
可以对下列编码器信号进行处理:
也可以使用 KTY84-130 或 PTC 热敏电阻来检测电机温度。
机柜安装式编码器模块 SMC30 标准提供有下列接口:
机柜安装式传感器模块 SMC30 的状态通过一个多色 LED 来显示。
SMC30 柜装式传感器模块可以安装在符合 EN 60715 (IEC 60715) 标准的 TH 35 高帽型导轨上。
SMC30 模板和编码器之间的大编码器电缆长度为 100 m。对于 HTL 编码器,如果对信号 A+/A- 和 B+/B- 进行分析,并且电源电缆的小截面积为 0.5 mm2,则此电缆长度可增加到 300 m。
信号电缆屏蔽线可以借助一个屏蔽线接线端子连接在编码器模块 SMC30 上,例如 Phoenix Contact 公司的 SK8 型号,或者 Weidmüller 公司的 KLBÜ 型号。
机柜安装式传感器模块 SMC30 通过 DRIVE-CliQ 与控制器 CU320-2 进行通讯。
SMC30 机柜安装式传感器模块 | |
规定电流,大 | 0.2 A |
| 2.5 mm2 |
| 20 A |
功耗 | < 10 W |
可评估的编码器 |
|
| |
| 576 Ohm |
| 16 mA |
| 24 V DC/0.35 A 或 5 V DC/0.35 A |
| 300 kHz |
| 100 … 250 kBaud |
| 300 kHz |
| 30 位 |
| |
| 100 m(仅允许双极信号)1) |
| 100 m,单极信号 |
| 100 m |
PE 连接 | M4 螺钉 |
尺寸 | |
| 30 mm |
| 150 mm |
| 111 mm |
重量,约 | 0.45 kg |
认证, | CULus |
BOP20 Basic Operator Panel
Parameters can be set, diagnostics information (e.g. alarm and fault messages) read out and faults acknowledged using the BOP20 Basic Operator Panel.
The BOP20 Basic Operator Panel has a backlit two-line display area with six keys.
The integrated plug connector on the rear of the BOP20 Basic Operator Panel provides its power and establishes communication with the Control Unit.
The BOP20 Basic Operator Panel can be inserted on the following Control Units:
Control Unit CU305 with attached BOP20 Basic Operator Panel
CU310‑2 PN Control Unit with inserted BOP20 Basic Operator Panel
CU320‑2 PN Control Unit with inserted BOP20 Basic Operator Panel