滑线变阻器使用手册
Slip-line manual rheostat

 概述..............................................2
 OVERVIEW .................................. .....2
 主要特点..........................................2
 Main Features.....................................2
 使用及维护........................................3
 Use and Maintenance...............................3
 使用条件及注意事项................................4
 Conditions of Use and Notice......................4
 安全注意事项......................................5
 Safety Precautions................................5
上海苏特电气有限公司

地址：上海市共康路1018号
：200443
： 徐寿平
电 话： 66241190
传 真： 56422486
手 机：
留 言：发送留言
个性化：www.cnsute.com
 

SHANGHAI SUTE ELECTRICAL CO,.TLD
使用本装置前请阅读本指南,阅读后请妥善保存，以备今后参阅
Use of this device before you read this guide

 概述：Overview
滑线式变阻器产品采用经过氧化绝缘处理的康铜丝，密绕于陶瓷管上，并固定于金属保护支架上，通过接触系统的导电电刷，在康铜丝表面移动，以达到改变阻值的大小，本产品在交直流电路中均适用，在电气机械设计阶段中作变更电流、电压和作为代替未定阻值的可变电阻器及负载之用，在实验室中作研究试验或教学演示用的电流、电压调节器，以及作为发电设备和直流电动机的励磁、调速电阻等之用。根据特殊要求可制作为无感，以保证严格环境下的使用要求。
slide-wire rheostat products are handled through the oxidation of high-quality health insulated copper wire, close around the ceramic tube and fixed on the metal protection stent, through the conductive brush contact system, in the Kang copper surface movement in order to achieve change in the size of the resistance, the products in the AC and DC circuits are applied in electrical machine design stage to change the current, voltage and resistance as a place of uncertain variable resistor and the load used in the laboratory for research testing or teaching demonstration using current, voltage regulators, as well as power generation equipment, and the excitation DC motor, speed-resistance and other purposes.According to special requirements can be made without a sense of environment to ensure the strict application requirements.
我司针对国内外各类客户的不同要求，不断开发出适用于各个领域的滑线式变阻器，通过长期的不断努力逐渐成为大的滑线式变阻器供应商。为电力、通讯、航天、等各行业及生产发电机组，变压器、UPS电源、蓄电池、太阳能、风能、焊机的用户和厂家及各大院校提供完整的解决方案。
I Division in response to the different requirements of customers from home and abroad, and continuously developed in various fields applied to slide-wire rheostat, through long-term ongoing efforts to become the nation's largest supplier of slide-wire rheostat. For electricity, communications, aerospace, and other industries and production generator sets, transformers, UPS power supply, battery, solar energy, wind energy, welding machine users and manufacturers and major institutions to provide a complete and efficient solution.

 主要特点：Main features
1、选用康铜材料,传统工艺，可靠性强。
Constantan use high-quality materials, traditional crafts, and reliability.
. 2、在连续工作状态下，温漂较小。
In the continuous mode, a smaller drift.
3、阻值/电流连续可调，精度高。
Resistance / current continuously adjustable, high accuracy.
4、内部结构布局合理,操作简便实用。
The internal structure of the layout is reasonable, easy to operate and practical.

 使用及维护：Use and maintenance
1、变阻器单台产品在电路中可作串、并联使用，也可多台并机使用。
Rheostat single products in the circuit can be used for series and parallel use can also be multiple, and machine use.
2、滑线变阻器的结构和符号如图所示，电阻丝的两头分别接在瓷管两端的A、B接线柱 上，A、B之间的电阻即为总电阻。滑动头D可沿金属杆滑动，与电阻丝接触良好，改 变其位置就可以改变AC（或BC）电阻。额定电流和总电阻等参数均在铭牌上标明。在 电路中有两种接法：
Slip-line rheostat of the structure and symbols shown in the figure, the resistance wire of the two were connected to the ceramic tube at both ends of A, B terminal on the, A, B shall be the total resistance between the resistor. Sliding head D can slide along the metal bars, with good contact resistance wire, changing its location can change the AC （or BC） resistance. Rated current and the total resistance and other parameters are indicated on the nameplate. In the circuit there are two kinds of access method:
①限流接法：将变阻器的一个固定端和滑动端接入电路，由于电阻可变，从而使电路中 的电流发生变化。
① limiting Connection: The rheostat on a fixed side and sliding side access to the circuit, due to the variable resistor, so that circuit current change.
②分压接法：将变阻器的两个固定端分别与电源的两极相连，由滑动端和任一固定端连 接到电路。由于电流通过变阻器的全部电阻丝，故A、B之间任意两点都有电势差。当 滑动头移动时，就改变了电路的输入电压。
注意：限流接法中，变阻器的滑动头应放在电阻zui大的位置；分压接法中，变阻器的滑 动头应放在分压zui小的位置。
② Partial Pressure Connection: The varistor of the two fixed end of the bipolar power supply, respectively connected by a sliding side and either a fixed terminal connected to the circuit. As the current through the varistor all the resistance wire, so A, B are any two points between the electrical potential difference. When sliding the first move, to change the circuit's input voltage.
Note: Limiting access law, rheostat sliding head should be placed on the location of the greatest resistance; sub crimping law, rheostat sliding head should be placed on the location of partial pressure of the smallest.

 使用条件及注意事项：Conditions of Use and Notice
１、请严格保证变阻器在额定电压及电流值下使用。
please ensure strict rheostat at rated voltage and current values to use.
２、变阻器是易发热元件，安装时不宜靠近不能受热的物体。
rheostat is easy to heating element, installation should not be close to the object can not be heated.
３、变阻器配有M6的安装孔及接地端子，保证使用时良好的地。
rheostat with M6 mounting holes and grounding terminals to ensure a good grounding when used.
４、变阻器使用如发生接触不良时，可在电刷接触面移动的康铜丝表面，除去氧化绝缘层， 即可消除其现象。
rheostat to use the event of being exposed, it can move in the brush contact surface Kang copper surface, remove the insulating oxide layer, you can eliminate the phenomenon.
６、变阻器经长时间的连续使用后，如发现滑片失去压力时，需拆下接触系统，把接触桥修 正（矫直），重新装上后，使电刷贴平于电阻丝表面，方可正常使用。
rheostat through a long period of continuous use, such as the vane was found to lose pressure, the need to remove the contact system to contact the bridge correction （straightening）, re-fitted after, so that resistance wire brush affixed flat on the surface, side can be used normally.

7、安装场所的空气中不应含化学腐蚀气体和蒸气，无爆炸性尘埃。the installation of air spaces should not be included chemical etching gases and vapors, non- explosive dust.
8、电阻器使用环境：resistors use of the environment
A:海拔高度不超过3000米。
A: height of not more than 3000 meters above sea level.
B:周围介质温度不高于+40℃及不低于-30℃。
B: the surrounding medium temperature is not higher than +40 ℃ and no less than -30 ℃.
C:空气相对温度不大于85%。
C: air relative humidity is not greater than 85%.
D:在有防雨设备及没有滴水蒸汽的地方。
D: in a rain-proof equipment and is not dripping steam areas.

 安全注意事项Safety Precautions
1、为了确保安全，本设备的操作请由充分理解本指南内容、具有安全操作知识和技能 的人进行。
In order to ensure safety, the operation of this device requested by the full understanding of the contents of this guide, with the safe operation of the knowledge and skills people.
2、请不要触摸带电部位。
Please do not touch the live parts.
3、请由有资格的电工进行本设备的安装，使用于绝缘手套。
Please carried out by a qualified electrician to install this device, used in insulating gloves.
4、检查或维修时，请一定要切断所有输入电源。接地线必须可靠接于大地，否则操作人员可能有触电危险。
Inspection or maintenance, be sure to cut off all input power. Grounding wire must be reliably connected to the earth, or else the operator may be an electric shock hazard.

上 海 苏 特 电 气 有 限 公 司
SHANGHAI SUTE ELECTRICAL CO.,LTD