塑料水平垂直阻燃试验机适用范围

    用于测试塑料类及非金属材料类物质燃烧性能的试验仪器。适用于塑料和非金属材料试样处于50W火焰条件下，水平或垂直方向燃烧性能的试验室测定方法。(实物如右图)

• 塑料水平垂直阻燃试验机产品功能特点

1. 微电脑控制操作
2. 自动化程度高：自动记录试验时间并可保存，自动显试结果，自动计时，自动点火，自动报警系统，施焰结束后本生灯自动退回
3. 水平、垂直燃烧试样夹电机控制
4. 记时准确

   三、相关技术参数

①仪器合适工作条件及主要技术指标

1. 环境温度：室温～40℃； 相对湿度：≤75％；
2. 供电电压和功率：220V±10％       50HZ     功率150W
3. 本生灯自动点火时间：任意设定
4. 本生灯内径9.5mm±0.5mm
5. 气源：液化石油气（仲裁时加工业甲烷气）；
6. 304全不锈钢箱体耐高温高湿高腐蚀环境
7. 燃烧箱内部容积：0.75立方米（不锈钢款）
8. 仪器重量约：100kg
9. 工作电源 ：  220V  AC  50HZ
10. 计时范围：0~999s 记时精度：10s±0.2s　30s±0.2s；
11. 施焰时间 ：  0～999.9S（可调）
12. 余焰时间 ：  0～999.9S（可调）
13. 余灼时间 ：  0～999.9S（可调）
14. 燃烧角度 ：  0°、20°、45°可选择
15. 火焰高度 ：  20mm ~ 175mm   可调
16. 火焰温度：（100-1000）℃可调
17. 气体流量 ：  0.03~ 0.3ml/Min
18. 燃 烧 灯 ：  灯管内径9.5±0.3mm,长度：100mm±10mm
19. 时间装置 ：  能精确到0．5S
20. 位置调节 ：  样品夹支架可上下、左右调节，燃烧座可前后调节，调节行程均大
21. 设备外形尺寸：0.75立方不锈钢款箱体 长*款*高1300*650*1200

②设计标准：

GB-T2408-2008《塑料燃烧性能的测试-水平法和垂直法》（ANSI/UL94 -2006）

③符合标准：

GB-T5455 《 纺织品 燃烧性能试验 垂直法》

GB-T13488《橡胶燃烧性能测定—垂直燃烧法》

GB/T5169.16-2002

ANSI/UL94

IEC60950-1、

IEC695-2-2

四、产品配置

1. 设备主机       壹台

1. 电源线         壹根         
2. 滴落盘         壹只              
3. 点火器         壹只     
4. 螺丝刀         壹只
5. 紧箍       贰个
6. 气源管         壹点伍米
7. 备用标尺    壹把
8. 说明书         壹份
9. 合格证       壹张

Product Name: Horizontal and vertical burning tester

Product Model:CZF-5

Design Standards ：GB/T2408-2008 Plastics. Determination of burning characteristics. Horizontal and vertical test

Brief Introduction :That horizontal and vertical burning tester is designed according to the chinese national standard《 GB/T2408-2008  Plastics. Determination of burning characteristics. Horizontal and vertical test》and meet the requirements of it compley。Both the horizontal and vertical burning test  can be completed in this machine。The test data can be recorded and saved automatically。It is also  suitable for the chinese national standard《 GB/T 5455 Textiles. Burning behaviour. Vertical method 》.And unlike the CZF-3 tester ,it^,s  more sophisticated and more automated。 The burning body is 0.5m3and that is larger than the CZF-3 tester。By the way， 0.5m3 is in accordance with UL94-2006 and GB-T2408-2008。

Design standard of the  horizontal and vertical burning tester  ：

GB-T2408-2008《  Plastics. Determination of burning characteristics. Horizontal and vertical test》

The standard can be meet: UL94-2006、GB-T 5455 、 GB-T13488 、GB-T5169、 IEC60695-11-3、IEC60695-11-4、IEC60950-1、IEC695-2-2

（一）The  environmental requirements

1.    Requirements about environmental temperature  : -10℃～30℃

2.    Relative humidity:≤85％

3.    Supply voltage and power:220V±10％ ,  50HZ  150W

(二)Characteristic

1. The diameter of the burner is 9.5mm+0.3mm，The diameter ofthe Bunsen burner is 9.5mm±0.5mm
2. There is a screw nut on the bunsen burner used to control the height of  blue flame
3. The auto-ignition time of the bunsen burner can be set up arbitrarily
4. it^，s tilt angle is between  0° and45°，EachInterval can be tilted 5 degrees automatically
5. You can djust the flame height between 20mm + 2mm and 100mm + 10mm
6. The bunsen burner move to the bottom of the test sample quickly  through the motor
7. The bunsen burner  return  automatically when the flame application completed
8. The flame applying time  of  the bunsen burner is between0～999.9S+0.1s and it can set up  automatically  within that band。the flame can set up between 20 and 175mm
9. The  afterflame time  can set up between 0 to 999.9S+0.1s and the tester will keep the minutes  automatically ，in addition，you can  pause it manually
10. The  residual burning time can set up between 0 and 999.9S+0.1s and the tester will keep the minutes  automatically ，in addition，you can  pause it manually
11. The source can sue 98% methane、 natural gas、 liquefied petroleum gas or  coal gas
12. Flux of the  methane can set up between 105ml/min and1000ml/min。
13. A electronic switch is  set on the gas pipeline
14. You should close the  The gas switch on the  panel when the test is  finish，around this time， the bunsen burnerwill in time go out of itself
15.  The burning body is 0.5m3and it has a black  background ，the  background illumination  must be 20Lux or less 。Moreover， we also have 0.75m3 burning body if it is  in need

the upper and lower left and right travel of  the sample frame must be 300mm or more  。There is a servo motor cotrol  the horizontal and vertical  distance   from test sample and  the flame

1.  The  flue gas  will  be discharged  by the ventilating fan who is   on the experimental box top when  the test finish
2. The whole test process is automatically controlled and the ventilation system is independent