德国 Unipower 负载监控器
德国 Unipower 负载监控器
德国 Unipower 负载监控器
德国 Unipower 负载监控器
德国 Unipower 负载监控器

APM382德国 Unipower 负载监控器

参考价: 面议

具体成交价以合同协议为准
2021-09-08 16:14:16
308
属性:
产地类别:进口;应用领域:环保,化工;颜色:白色;
>
产品属性
产地类别
进口
应用领域
环保,化工
颜色
白色
关闭
北京凯盛源科技有限公司

北京凯盛源科技有限公司

初级会员4
收藏

组合推荐相似产品

产品简介

德国 Unipower 负载监控器
Unipower基于电功率测量提供测量和监控电子设备制造商,该原理允许持续考虑电力驱动器的负载情况,从而对系统进行在线监控和保护,装配在控制柜的过程级别之外进行。

详细介绍

德国 Unipower 负载监控器

德国 Unipower 负载监控器

UNIPOWER  产品一览表

UNIPOWER APM10:千瓦变送器


   *尺寸:DxWxH = 58 x 36 x 86 mm

   *三相对称kW测量

   *测量电压:

     3 x 100Vac-3 x 500Vac(一台)

   *电源电压24Vdc

   *使用内部CT直接测量高达60A

     -否则外部CT N / 5

   *精度:符合EN 61036的2级

   * 6个电流范围:5A,10A,20A,25A,40A,60A

   * 0(4)-20mA或0(2)-10V模拟输出


   * CE标志

UNIPOWER  APM10: kW-transmitter


  * Dimensions: DxWxH = 58 x 36 x 86 mm

  * 3-phased symmetric kW-measurement

  * Measuring voltage:

    3 x 100Vac - 3 x 500Vac with one unit

  * Supply voltage 24Vdc

  * Direct measurement up to 60A with internal CT

    - otherwise external CT N/5

  * Accuracy: Class 2 according to EN 61036

  * 6 current ranges: 5A, 10A, 20A, 25A, 40A, 60A

  * 0(4)-20mA or 0(2)-10V analogue outputs


  * CE-mark


UNIPOWER APM100B:千瓦测量传感器


   *尺寸:DxWxH = 58 x 70 x 86 mm

   *三相对称kW测量

   *测量和电源电压:

     3 x 380Vac-3 x 500Vac带一个单元

   *通过内部CT直接测量高达80A

     -否则外部CT N / 5

   *精度:符合EN 61036的2级

   *以kW为单位的范围设置:

     从0.1kW到70kW,以0.1kW为步长

   * 0(4)-20mA以及0(2)-10V模拟输出

   * kWh输出(SO-1):

     满刻度100或300脉冲/小时

   *内置滤波器功能-平均16倍


UNIPOWER APM100B: Measurement transducer for kW


  * Dimensions: DxWxH = 58 x 70 x 86 mm

  * 3-phased symmetric kW-measurement

  * Measuring- and supply voltage:

    3 x 380Vac - 3 x 500Vac with one unit

  * Direct measurement up to 80A with internal CT

    - otherwise external CT N/5

  * Accuracy: Class 2 according to EN 61036

  * Range setup in kW:

    from 0.1kW to 70kW in steps of 0.1kW

  * 0(4)-20mA as well as 0(2)-10V analogue outputs

  * kWh-output (SO-1):

    100 or 300 pulses/hour at full scale

  * Built-in filter function - 16x averaging


  * CE-mark



UNIPOWER APM110:具有1个最大限制和1个最小限制的Loadmonitor

       ** 低成本 **


   *尺寸:DxWxH = 58 x 70 x 86 mm

   *测量和电源电压:

     3 x 380Vac-3 x 500Vac带一个单元

   *通过内部CT直接测量高达80A

     -否则外部CT N / 5

   *直接测量高达70kW

   *范围=最大限制,以kW为单位设置

   *限额:

     20%-> 80%的范围,以4%为步长

   *开始时间和反应时间:

     0-10秒 (最小限制为20秒)

   *手动和自动重置


   * CE标志

UNIPOWER APM110: Loadmonitor with 1 Max- and 1 Min-limit

      ** Low Cost **


  * Dimensions: DxWxH = 58 x 70 x 86 mm

  * Measuring- and supply voltage:

    3 x 380Vac - 3 x 500Vac with one unit

  * Direct measurement up to 80A with internal CT

    - otherwise external CT N/5

  * Direct measurement up to 70kW

  * Range = Max-limit, setup in kW

  * Min-limit:

    20% -> 80% of range in steps of 4%

  * Start- and reactiontimers:

    0 - 10 sec. (20 sec for Min-limit)

  * Manuel and auto-Reset


  * CE-mark


UNIPOWER APM110E:具有1个最大限制和1个最小限制的Loadmonitor

       ** 低成本 **


   *尺寸:DxWxH = 58 x 70 x 86 mm

   *测量电压:

     3 x 230Vac-3 x 575Vac带一个单元

   * 电源电压:

     1 x 110Vac或1 x 230Vac(带一个单元)

   *可以连接到外接人机界面

     -Unipower PCU d10

   *作为APM110的功能


   * CE标志和cUL批准的Fileno。 E194022

UNIPOWER APM110E: Loadmonitor with 1 Max- and 1 Min-limit

      ** Low Cost **


  * Dimensions: DxWxH = 58 x 70 x 86 mm

  * Measuring voltage:

    3 x 230Vac - 3 x 575Vac with one unit

  * Supply voltage:

    1 x 110Vac or 1 x 230Vac with one unit

  * May be connected to external display unit

    - Unipower PCU d10

  * Functionality as APM110


  * CE-mark and cUL-approved, Fileno. E194022




UNIPOWER APM300B:千瓦测量传感器


   *尺寸:DxWxH = 58 x 36 x 86 mm

   *三相非对称kW测量

   *测量和电源电压:

     可提供3x230Vac-3 x 575Vac

   *连接到外部CT-N / 1或N / 5

   *精度:符合EN 61036的2级

   * 0(4)-20mA以及0(2)-10V模拟输出

   * kWh输出(SO-1):

     满量程1000脉冲/小时

   *内置滤波器功能-平均16倍


   * CE标志

UNIPOWER APM300B: Measurement transducer for kW


  * Dimensions: DxWxH = 58 x 36 x 86 mm

  * 3-phased asymmetric kW-measurement

  * Measuring- and supply voltage:

    available from 3x230Vac - 3 x 575Vac

  * Connected to external CTs - N/1 or N/5

  * Accuracy: Class 2 according to EN 61036

  * 0(4)-20mA as well as 0(2)-10V analogue outputs

  * kWh-output (SO-1):

    1000 pulses/hour at full scale

  * Built-in filter function - 16x averaging


  * CE-mark




UNIPOWER APM380:千瓦测量传感器


   *尺寸:DxWxH = 58 x 105 x 86 mm

   *用于测量的三相非对称kW-meter

     -同样在变频器之后

   *频率范围10Hz-1kHz

   *适用于电源电压:

     从3 x 230Vac到3 x 575Vac

   *内部可测量高达80A的电流

   * 7个标称电压范围

   * 10个标称电流范围为1A至80A

   * 4个可编程模拟滤波器特性

   * 3个可编程数字滤波器特性

   * 2个模拟输出(电流隔离):

     0(4)-20毫安

     0(2)-10伏

   * S0-1输出为kWh(1或10 imp./kWh)


   * CE标志和cUL批准的Fileno。 E350194

UNIPOWER APM380: Measurement transducer for kW


  * Dimensions: DxWxH = 58 x 105 x 86 mm

  * 3-phased asymmetric kW-meter for measurement

    - also after frequency inverter

  * Frequency range 10Hz - 1kHz

  * Suitable for mains voltages:

    from 3 x 230Vac to 3 x 575Vac

  * Measures current up to 80A internally

  * 7 nominal voltage ranges

  * 10 nominal current ranges from 1A to 80A

  * 4 programmable analogue filter characteristics

  * 3 programmable digital filter characteristics

  * 2 analogue outputs (galvanic isolated):

    0(4)-20mA

    0(2)-10V

  * S0-1 output for kWh (1 or 10 imp./kWh)


  * CE-mark and cUL-approved, Fileno. E350194




UNIPOWER APM382:千瓦测量传感器

         具有控制功能


   *尺寸:DxWxH = 58 x 105 x 86 mm


   *具有APM380之类的功能,并具有其他功能:

   *通过PC通过RS232进行设置

     (包括软件)

   * 2个光耦合器输出

   * 2个独立限制

   * dP / dt监督

   *缩放功能:满刻度= 10-100%

   *模拟输出可能反相:

     (20-0(4)mA)


   * CE标志和cUL批准的Fileno。 E350194

UNIPOWER APM382: Measurement transducer for kW

        with control functions


  * Dimensions: DxWxH = 58 x 105 x 86 mm


  * Features like APM380 with extra functions:

  * Setup via PC over RS232

    (Software included)

  * 2 optocoupler outputs

  * 2 independant limits

  * dP/dt supervision

  * Zoom function: Full Scale = 10-100%

  * Possible inverting of the analogue outputs:

    (20 - 0(4) mA)


  * CE-mark and cUL-approved, Fileno. E350194




UNIPOWER APM426:用于2速应用程序的负载监视器


   *尺寸:DxWxH = 58 x 105 x 86 mm

   *通过数字输入选择有效极限

   *三相非对称功率计

     也用于变频器后的测量

   *适用于电源电压:

     从3 x 230Vac到3 x 575Vac

   *内部可测量高达30A的电流

   *通过PC通过RS232进行设置

     (包括软件)

   * 2个光耦合器输出

   *每个限制的可选类型(最大或最小)


   * CE标志和cUL批准的Fileno。 E350194

UNIPOWER APM426: Load Monitor for 2-speed applications


  * Dimensions: DxWxH = 58 x 105 x 86 mm

  * Active limit selected via digital input

  * 3-phased asymmetric kW-meter

    also for measurement after frequency inverter

  * Suitable for mains voltages:

    from 3 x 230Vac to 3 x 575Vac

  * Measures current up to 30A internally

  * Setup via PC over RS232

    (Software included)

  * 2 optocoupler outputs

  * Optional type for each limit (Max or Min)


  * CE-mark and cUL-approved, Fileno. E350194




UNIPOWER APM450:用于变速应用的负载监控器


   *尺寸:DxWxH = 58 x 105 x 86 mm

   *取决于速度的设定值

   *自动测量速度(频率)

   *三相非对称功率计

     也用于变频器后的测量

   *适用于电源电压:

     从3 x 230Vac到3 x 575Vac

   *内部可测量高达30A的电流

   *通过PC通过RS232进行设置

UNIPOWER APM450: Load Monitor for variable speed applications


  * Dimensions: DxWxH = 58 x 105 x 86 mm

  * Speed dependent setpoints

  * Automatic measurement of speed (Frequency)

  * 3-phased asymmetric kW-meter

    also for measurement after frequency inverter

  * Suitable for mains voltages:

    from 3 x 230Vac to 3 x 575Vac

  * Measures current up to 30A internally

  * Setup via PC over RS232

    (Software included)

  * 2 optocoupler outputs

  * Two independent limits (Max and Min)


  * CE-mark and cUL-approved, Fileno. E350194




UNIPOWER DSU d382:不带控制功能的人机界面


   *尺寸:DxWxH = 70 x 72 x 72 mm

   *与APM382一起使用

   *通过RS232连接

   * APM382编程

   *显示测量结果为kW%

   *显示监督状态:

     -警报条件

-计时器

     -输出位置


   * CE标志

UNIPOWER DSU d382: Display unit without control functions


  * Dimensions: DxWxH = 70 x 72 x 72 mm

  * Used together with APM382

  * Connection via RS232

  * Programming of APM382

  * Shows measurements as kW%

  * Shows status of supervision:

    - Alarm conditions

- Timers

    - Output positions


  * CE mark


UNIPOWER DSU d382-DAQ:具有数据采集功能的显示单元


   *尺寸:DxWxH = 70 x 72 x 72 mm

   *与APM382一起使用

   *通过RS232连接

   *与PCU d382 +数据采集相同:

     -

     -采集间隔从20ms到1s

     -数据传输到PC

     -使用专用软件UniDAQ进行数据处理

       (包含)


   * CE标志

UNIPOWER DSU d382-DAQ: Display unit with Data acquisition


  * Dimensions: DxWxH = 70 x 72 x 72 mm

  * Used together with APM382

  * Connection via RS232

  * Same as PCU d382 + data acquisition:

    - Manual-, trigger- or permanent acquisition

    - Acquisition interval from 20ms to 1s

    - Transfer of data to PC

    - Data processing with special software UniDAQ

      (Included)


  * CE mark


UNIPOWER HC320:具有2个独立限制的通用控制器


   *尺寸:DxWxH = 58 x 36 x 86 mm

   *模拟输入:0(4)-20 mA

   *缩放功能:10-20 mA时100%

   * 2个继电器输出

   *可选的最大-或最小-限制

   *启动计时器和响应计时器

   *两个极限都有滞后功能

   *数字输入:

     可选高电平或低电平


   * CE标志

UNIPOWER HC320: Universal controller with 2 independent limits


  * Dimensions: DxWxH = 58 x 36 x 86 mm

  * Analogue input: 0(4) - 20 mA

  * Zoom function: 100% at 10 - 20 mA

  * 2 relay outputs

  * Optional max.- or min.- limits

  * Start timer and respons timers

  * Hysteresis function on both limits

  * Digital inputs:

    Optional active high or low


  * CE-mark



UNIPOWER HPL103A:千瓦测量传感器


   *尺寸:DxWxH = 112 x 72 x 72 mm

   *三相对称功率表

   *显示kW和[%kW]

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4(0)-20mA,电气隔离

   *可扩展的模拟输出(缩放功能)

   *功率测量的最大/最小峰值检测器

   * kWh输出(0.1、1或10 kWh pr。脉冲)


   * CE标志

UNIPOWER HPL103A: Measurement transducer for kW


  * Dimensions: DxWxH = 112 x 72 x 72 mm

  * 3-phased symmetric kW-meter

  * Display of kW and [%kW]

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4(0)-20mA, galvanic isolated

  * Scalable analogue output (zoom function)

  * Max/Min-peak detector of kW measurement

  * kWh-output (0.1, 1 or 10 kWh pr. pulse)


  * CE-mark



UNIPOWER HPL110:具有1个最大限制和1个最小限制的Loadmonitor


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *以[%kW]为单位显示和编程极限

   *手动或自动重置

   *启动时间和反应时间的编程:

     0.1-99.9秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   * HPL420的低成本版本

   *最大/最小峰值检测器


   

UNIPOWER HPL110: Loadmonitor with 1 Max- and 1 Min-limit


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Display and programming of limits in [%kW]

  * Manuel or automatic reset

  * Programming of start- and reactiontimer:

    0.1 - 99.9 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Low cost version of HPL420

  * Max/Min-peak detectors


  * CE-mark and cUL-approved, Fileno. E194022


UNIPOWER HPL110A:具有1个最大限制和1个最小限制的负载监控器


   *尺寸:DxWxH = 112 x 72 x 72 mm

   *以[%kW]为单位显示和编程极限

   *手动或自动重置

   *启动时间和反应时间的编程:

     0.1-99.9秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *最大/最小峰值检测器


   * CE标志


UNIPOWER HPL110A: Loadmonitor with 1 Max- and 1 Min-limit


  * Dimensions: DxWxH = 112 x 72 x 72 mm

  * Display and programming of limits in [%kW]

  * Manuel or automatic reset

  * Programming of start- and reactiontimer:

    0.1 - 99.9 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Max/Min-peak detectors


  * CE-mark


UNIPOWER HPL130A:具有1个最大和1个dP / dt限制的Loadmonitor


   *尺寸:DxWxH = 112 x 72 x 72 mm

   *以[%kW]为单位显示和编程极限

   *启动时间和反应时间的编程:

     0.1-25.0瑞典克朗。

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *也可用于直流输入:

     0(4)-20mA,输入比例:10(12)-20mA

   *最大和dP / dt峰值检测器


   * CE标志


UNIPOWER HPL130A: Loadmonitor with 1 Max- and 1 dP/dt-limit


  * Dimensions: DxWxH = 112 x 72 x 72 mm

  * Display and programming of limits in [%kW]

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sek.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Available also for DC-input:

    0(4)-20mA, scaling of input: 10(12)-20mA

  * Max- and dP/dt-peak detectors


  * CE-mark


HPL220:测量传感器

         具有集成控制功能


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *输入:

     a)差分20-100mV可编程范围

     b)0-20mA

     c)0-10V

   *内置激励电压10V / 30mA

     (例如称重传感器)

   * 2个活动极限(最大或最小可选)

   *以[%kW]为单位显示和编程极限

   *启动和反应计时器的编程:

     0.1-25.0瑞典克朗。

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *电源电压:24Vdc

   *模拟输出:

     Iout 4-20mA,不隔离电流

   *最大/最小峰值检测器


   * CE标志


UNIPOWER HPL220: Measurement transducer

        with integrated control functions


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Input:

    a) differential 20-100mV programmable range

    b) 0-20mA

    c) 0-10V

  * Built-in excitation voltage 10V/30mA

    (e.g. load cell)

  * 2 active limits (Max. or Min selectable)

  * Display and programming of limits in [%kW]

  * Programming of start- and reaction timer:

    0.1 - 25.0 sek.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Supply voltage: 24Vdc

  * Analogue output:

    Iout 4-20mA, NOT galvanic isolated

  * Max/Min-peak detectors


  * CE-mark

UNIPOWER HPL403:千瓦测量传感器


**对于新应用,请参考HPL500 **


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *三相对称功率表

   *显示kW和[%kW]

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout(电隔离):

     4(0)-20毫安

     Vout 2(0)-10V

   *可扩展的模拟输出(缩放功能)

   *功率测量的最大/最小峰值检测器

   * kWh输出(1或10 kWh脉冲)


   * CE标志和cUL批准的Fileno。 E194022



UNIPOWER HPL403: Measurement transducer for kW


** For new applications please refer to HPL500 **


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * 3-phased symmetric kW-meter

  * Display of kW and [%kW]

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue outputs Iout (galvanic isolated):

    4(0)-20mA

    Vout 2(0)-10V

  * Scalable analogue outputs (zoom function)

  * Max/Min-peak detector of kW measurement

  * kWh-output (1 or 10 kWh pr. pulse)


  * CE-mark and cUL-approved, Fileno. E194022


UNIPOWER HPL410:具有1个最大或最小限制的负载监控器




  


   请参考HPL500

 *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   * 2个独立限制

   *可以计算轴功率


   * CE标志和cUL批准的Fileno。 E194022

   * GOST-R认证



   文档仍然可用



UNIPOWER HPL410: Loadmonitor with 1 Max- or Min-limit




  Unit no longer in production!


  Please refer to HPL500


  Documentation still available


UNIPOWER HPL411:Load Monitor具有1个最大限制和

         ut Po补偿


   *尺寸:DxWxH = 110 x 56 x 75 mm

   * HPL410的特殊版本。

     专为Justsen Energiteknik A / S设计

              DK-8600 Randers,电话:+45 86260500


   *以[%kW]为单位显示和编程极限

   *启动时间和反应时间的编程:

     0.1-25.0瑞典克朗。

   *手动或自动重置

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大/最小峰值检测器



   * CE标志和cUL批准的Fileno。 E194022

UNIPOWER HPL411: Loadmonitor with 1 Max limit and

        aut. Po-compensation


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Special version of HPL410.

    Made for Justsen Energiteknik A/S

             DK-8600 Randers, Tel: +45 86260500


  * Display and programming of limits in [%kW]

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sek.

  * Manual or automatic reset

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max/Min-peak detectors


  * CE-mark and cUL-approved, Fileno. E194022

UNIPOWER HPL412:具有1个最大限制和

         ut Po补偿


   *尺寸:DxWxH = 110 x 56 x 75 mm

   * HPL410的特殊版本。

     专为Justsen Energiteknik A / S设计

              DK-8600 Randers,电话:+45 86260500


   *以[%kW]为单位显示和编程极限

   *启动时间和反应时间的编程:

     0.1-25.0瑞典克朗。

   *手动或自动重置

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大/最小峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL412: Loadmonitor with 1 Max limit and

        aut. Po-compensation


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Special version of HPL410.

    Made for Justsen Energiteknik A/S

             DK-8600 Randers, Tel: +45 86260500


  * Display and programming of limits in [%kW]

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sek.

  * Manual or automatic reset

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max/Min-peak detectors


  * CE-mark and cUL-approved, Fileno. E194022



UNIPOWER HPL420:具有1个最大限制和1个最小限制的Loadmonitor


**对于新应用,请参考HPL500 **


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *以[%kW]为单位显示和编程极限

   *相序监督

   *启动时间和反应时间的编程:

     0.1-25.0秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大/最小峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL420: Loadmonitor with 1 Max- and 1 Min-limit


** For new applications please refer to HPL500 **


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Display and programming of limits in [%kW]

  * Phase order supervision

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max/Min-peak detectors


  * CE-mark and cUL-approved, Fileno. E194022


UNIPOWER HPL425:具有2个最大限制的负载监控器,两个限制均处于活动状态


**对于新应用,请参考HPL500 **


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *以[%kW]为单位显示和编程极限

   *相序监督

   *启动时间和反应时间的编程:

     0.1-25.0秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL425: Loadmonitor with 2 Max limits, both limits active


** For new applications please refer to HPL500 **


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Display and programming of limits in [%kW]

  * Phase order supervision

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max peak detector


  * CE-mark and cUL-approved, Fileno. E194022

UNIPOWER HPL426:具有2个最大限制的Loadmonitor,

         2种速度应用(起重机)

         可通过数字输入选择


**对于新应用,请参考HPL500 **


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *以[%kW]为单位显示和编程极限

   *相序监督

   *启动时间和反应时间的编程:

     0.1-25.0秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL426: Loadmonitor with 2 Max limits,

        2 speed applications (cranes)

        selectable via digital input


** For new applications please refer to HPL500 **


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Display and programming of limits in [%kW]

  * Phase order supervision

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max peak detector


  * CE-mark and cUL-approved, Fileno. E194022


UNIPOWER HPL430:具有1个最大和1个dP / dt限制的Loadmonitor


**对于新应用,请参考HPL530 **


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *以[%kW]为单位显示和编程极限

   *相序监督

   *启动时间和反应时间的编程:

     0.1-25.0秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大和dP / dt峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL430: Loadmonitor with 1 Max- and 1 dP/dt-limit


** For new applications please refer to HPL530 **


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Display and programming of limits in [%kW]

  * Phase order supervision

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max- and dP/dt peak detector


  * CE-mark and cUL-approved, Fileno. E194022


UNIPOWER HPL431:具有1个最大和1个dP / dt限制的Loadmonitor



特别版本为:


   Simatek散装系统A / S



UNIPOWER HPL431: Loadmonitor with 1 Max- and 1 dP/dt-limit



Special version made for:


  Simatek Bulk System A/S

UNIPOWER HPL432:具有1个最大和1 +/- dP / dt限制的Loadmonitor


**对于新应用,请参考HPL530 **


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *以[%kW]为单位显示和编程极限

   *相序监督

   *启动时间和反应时间的编程:

     0.1-25.0秒

   *可编程迟滞带:

     2-50%(在自动重设模式下)

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大和dP / dt峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL432: Loadmonitor with 1 Max- and 1 +/- dP/dt-limit


** For new applications please refer to HPL530 **


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Display and programming of limits in [%kW]

  * Phase order supervision

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sec.

  * Programmable hysteresis band:

    2-50% (In Autoreset-mode)

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max- and dP/dt peak detector


  * CE-mark and cUL-approved, Fileno. E194022

UNIPOWER HPL440:具有自动换向的负载监控器




     *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   *可编程的反向尝试次数

   *可编程的反向时间:0.5-25 sek。

   *可以计算轴功率


   * CE标志和cUL批准的Fileno。 E194022

   * GOST-R认证



   文档仍然可用HPL440: Loadmonitor with automatic reversing




  Unit no longer in production!


  Please refer to HPL540


  Documentation still available



UNIPOWER HPL450:负载监控器,其频率已适应最大限制


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *频率输入:

     0-20mA(HPL450)

     0-10V(HPL451)

     10-1000Hz(HPL452)

     10-1000Hz NAMUR(HPL453)

   *以[%kW]为单位显示和编程极限

   *启动时间和反应时间的编程:

     0.1-25.0秒

   *适用于电压:

     从3 x 120Vac-> 3 x 660Vac

   *内部电流转换器高达8Aac

   *外部电流转换器N / 1或N / 5

   *模拟输出Iout 4-20mA,电流隔离

   *最大/最小峰值检测器


   * CE标志和cUL批准的Fileno。 E194022


UNIPOWER HPL450: Loadmonitor with frequency adapted Max.-limit


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Frequency input:

    0-20mA (HPL450)

    0-10V (HPL451)

    10-1000Hz (HPL452)

    10-1000Hz NAMUR (HPL453)

  * Display and programming of limits in [%kW]

  * Programming of start- and reactiontimer:

    0.1 - 25.0 sec.

  * Available for voltages:

    from 3 x 120Vac -> 3 x 660Vac

  * Internal current converter up to 8Aac

  * External current converter N/1 or N/5

  * Analogue output Iout 4-20mA, galvanic isolated

  * Max/Min-peak detectors


  * CE-mark and cUL-approved, Fileno. E194022

UNIPOWER HPL500:负载监控器,可计算轴功率


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   * 2个独立限制

   *可以计算轴功率


   * CE标志和cUL批准的Fileno。 E194022

   * GOST-R认证


UNIPOWER HPL500: Loadmonitor with calculation of shaft power


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Universal power supply:

    - Single phase: 1 x 100V - 1 x 400V

    - Three phase: 3 x 100V - 3 x 575V

  * Measuring voltage = Supply voltage

  * Current range: 0.5A - 40A internal

  * 2 independent limits

  * Can compute shaft power


  * CE mark and cUL-approved, Fileno. E194022

  * GOST-R certified

UNIPOWER HPL500-MB:具有Modbus接口的HPL500


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   * 2个独立限制

   *可以计算轴功率


UNIPOWER HPL500-MB: HPL500 with Modbus interface


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Universal power supply:

    - Single phase: 1 x 100V - 1 x 400V

    - Three phase: 3 x 100V - 3 x 575V

  * Measuring voltage = Supply voltage

  * Current range: 0.5A - 40A internal

  * 2 independent limits

  * Can compute shaft power


  * CE mark and cUL-approved, Fileno. E194022

  * GOST-R certified

UNIPOWER HPL500H:遥控器/显示单元

          没有控制功能


   *与HPL500-MB一起使用

   *通过Modbus连接

   * HPL500-MB的编程

   *以kW和kW%显示测量值

   *显示监督状态:

     -警报条件

     -计时器

     -输出位置


   * CE标志


UNIPOWER HPL500H: Remote control / Display unit

         without control functions


  * Used together with HPL500-MB

  * Connection via Modbus

  * Programming of HPL500-MB

  * Shows measurements as kW and kW%

  * Shows status of supervision:

    - Alarm conditions

    - Timers

    - Output positions


  * CE mark

UNIPOWER HPL530:具有1个最大和1个dP / dt限制的Loadmonitor


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   * 2个独立限制

   *可以计算轴功率


   * CE标志和cUL批准的Fileno。 E194022

   * GOST-R认证


UNIPOWER HPL530: Loadmonitor with 1 Max- and 1 dP/dt-limit


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Universal power supply:

    - Single phase: 1 x 100V - 1 x 400V

    - Three phase: 3 x 100V - 3 x 575V

  * Measuring voltage = Supply voltage

  * Current range: 0.5A - 40A internal

  * 2 independent limits

  * Can compute shaft power


  * CE mark and cUL-approved, Fileno. E194022

  * GOST-R certified

UNIPOWER HPL540:具有自动换向的负载监控器


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   *可编程的反向尝试次数

   *可编程的反向时间:0.5-25 sek。

   *可以计算轴功率


   * CE标志和cUL批准的Fileno。 E194022

   * GOST-R认证


UNIPOWER HPL540: Loadmonitor with automatic reversing


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Universal power supply:

    - Single phase: 1 x 100V - 1 x 400V

    - Three phase: 3 x 100V - 3 x 575V

  * Measuring voltage = Supply voltage

  * Current range: 0.5A - 40A internal

  * Programmable number of reverse attempts

  * Programmable reverse time: 0.5 - 25 sek.

  * Can compute shaft power


  * CE mark and cUL-approved, Fileno. E194022

  * GOST-R certified

UNIPOWER HPL580:带有轴功率计算的负载监控器


   *以%,kW和HP为单位的测量值显示

   *以%,kW和HP设置设定点


   *尺寸:DxWxH = 110 x 56 x 75 mm

   *通用电源:

     -单相:1 x 100V-1 x 400V

     -三相:3 x 100V-3 x 575V

   *测量电压=电源电压

   *电流范围:内部0.5A-40A

   * 2个独立限制

   *可以计算轴功率


   * CE标志和cUL批准的Fileno。 E194022

   * GOST-R认证


UNIPOWER HPL580: Loadmonitor with calculation of shaft power


  * Display of measurement in %, kW & HP

  * Setup of setpoints in %, kW & HP


  * Dimensions: DxWxH = 110 x 56 x 75 mm

  * Universal power supply:

    - Single phase: 1 x 100V - 1 x 400V

    - Three phase: 3 x 100V - 3 x 575V

  * Measuring voltage = Supply voltage

  * Current range: 0.5A - 40A internal

  * 2 independent limits

  * Can compute shaft power


  * CE mark and cUL-approved, Fileno. E194022

  * GOST-R certified


UNIPOWER PCU d10:具有控制功能的人机界面


   *尺寸:DxWxH = 70 x 72 x 72 mm

   *与APM110E一起使用

   *连接仅为2线制

   **接管APM110E

   *以kW%,kW或HP为单位显示测量/设定点

   *无源4-20mA模拟输出


   * CE标志


UNIPOWER PCU d10: Display unit with control functions


  * Dimensions: DxWxH = 70 x 72 x 72 mm

  * Used together with APM110E

  * Connection is only a 2-wire

  * Takes over APM110E completely

  * Shows measurements/setpoints in kW%, kW or HP

  * Passive 4-20mA analogue output


  * CE-mark



上一篇:便携式悬浮物检测仪—轻巧智能走哪测哪的便携式水质测定仪2024全+境+派+送 下一篇:水中油分析仪的应用领域有哪些?
热线电话 在线询价
提示

请选择您要拨打的电话:

当前客户在线交流已关闭
请电话联系他 :