OLYMPUS/奥林巴斯 品牌
代理商厂商性质
北京市所在地
奥林巴斯HSMT-Flex扫查器
HSMT-Flex™用于对4.5英寸管道上的圆周焊缝进行单轴编码检查。外型(114.3毫米)及以上。扫描仪配备了四个探针支架,但可以安装共八个探针与可选的探针支架。安装的探头可以是相控阵探头,也可以是常规UT探头,以实现有效的检测。
扫描仪的主要特点是其中心弯曲的能力。这使得扫描器可以安装在更小的管道上,并将弹簧加载臂的力带入管道的径向,从而更好地稳定楔块,从而获得数据采集。出于同样的原因,安装在扫描仪外部的可选探头支架也可以旋转。
HSMT-Flex还允许它的一个侧框架滑动。该特性允许将探头安装在扫描仪的外部。这提供了一种配置,非常适合于难以到达的地方,如管道到组件的焊接。
奥林巴斯HSMT-Flex扫查器
标准的夹杂物
•扫描仪框架与处理,并:
◦配置两个340毫米(13.5英寸)的框架酒吧
◦配置两个500毫米(20英寸)框架杆
•与omniscan兼容的防水弹簧加载车轮编码器与5米电缆
•90º探针托架
•4个弹簧加载臂(SLA)
•4 TOFD-P/E 31.75 mm轭架
•2pa 40mm×55mm轭架
•灌溉管和配件
注意:扫描仪不包括脐带、探头和楔。
选项
•脐
•远程脉冲发生器/前置放大器
•Couplant-Feed单位
•激光引导设备
电池驱动的激光引导装置,更容易跟踪焊缝。
•轭
•TomoScan聚焦LT编码器电缆适配器
•更换编码器
•探头夹包
组两个弹簧臂(SLA)安装在90º括号,允许超过四探针。
◦配置大于12英寸的管道。OD。
◦配置配置小于12英寸的管道。OD。
•备件包
◦pv - 100应用程序
◦pv - 200应用程序
The HSMT-Flex™ is intended for one axis encoded inspection of circumference welds on pipes of 4.5 in. OD (114.3 mm) and greater. The scanner comes equipped with four probe holders but can be mounted with a total of eight probes with optional probe holders. Mounted probes can be either phased array or conventional UT for most efficient inspections.
The major characteristic of the scanner is its capacity to bend in the center. This allows the scanner to fit on smaller pipes and also to bring the force of the spring-loaded arm in the radial direction of the pipes for better stability of the wedge, and therefore, optimum data acquisition. For the same reason, optional probe holders that are installed on the outside of the scanner can also pivot.
The HSMT-Flex also allows one of its side frames to slide. This feature allows having the probes mounted on the outside of the scanner. This provides a configuration that is well-suited for hard-to-reach places such as pipe-to-component welds.
Note: Umbilical cable, probes, and wedges are not included with the scanner.
Length in Scan Axis (mm) | Width (mm) | Height (mm) | Weight (kg) |
263 | 466 | 147 | 4.4 |